Design Mix Of Heavy Density Concrete Using Used Copper Slag

Behavior of Copper Slag Admixed Concrete in Acidic Environment ... Sand is majorly used fine aggregate in the preparation of concrete, however heavy depletion of river beds and rising cost of sand have made the builders and construction industry to ... Mix Design and Different Mixes Mix Design was done as per the code book, IS: 10262 – ...

This paper reports the effect of concrete using copper slag as fine aggregate replacement. In this project work, the concrete grade M40 was selected and IS method was used for mix design. The properties of material for cement, fine aggregate, coarse aggregate and copper slag were studied for mix design. The various strength of concrete

There have been researches done where copper slag was used as fine aggregate (up to 30%) or filler in the design of bituminous mixes like Bituminous Macadam, Dense Bituminous Macadam, Bituminous Concrete and Semi-Dense Bituminous Concrete.

already found it possible to use copper slag as a concrete aggregate. But not much ... The specific gravity of the slag is 3.91. The bulk density of granulated copper slag is varying from 1.9 to 2.15 kg/ m 3 which is almost similar to the bulk density ... 3.1. Mix design and sample preparation ...

Concrete contain cement, water, fine aggregate, coarse aggregate for normal concrete of ratio 1:1.2:2.3. The copper slag is used as partial replacement for fine aggregate in the range of 10%, 20% and 30% by weight of sand and Grade Cement Water Fine aggregate . Coarse aggregate . M25 450 197 580 1040

durability properties of M20 and M30 grade copper slag concrete. The results showed that addition of copper slag increases the density of concrete there by increasing the self-weight. The optimum % of copper slag for both the mixes (M20 and M30) was found to be 40%. The durability results showed the copper slag concrete has a

Oct 10, 2017 Dr. A. Leema rose et. Al. [2015] they find out solution and addition of copper scum use in concrete raises the density in concrete mixture scum by load of fine aggregate exchange 30% of replacement. It is also accomplished that the concrete through copper slag gains more strength than the manage concrete.

Concrete Mix Design - SlideShare; 29 Mar 2015 ... Concrete Mix Design Unit-III. ... Design Mix Concrete; 20. ... the main bars or 5 mm less the minimum cover to the reinforcement, whoever is smaller. ... of the fine and coarse aggregate in a concrete mix is one of the important... Get More Details. Article 8 Copper Slag Authors - Journal of ...

concrete beam with copper slag. To determine the optimum percentage of copper slag content (various mix proportions) for enhance the strength properties of concrete.Mix design for Self Compacting Concrete with water cement ratio of 0.40 is to be …

turing copper. Copper slag used in this work was brought from Sterlite Industries Ltd, Tuticorin, Tamil Nadu, India. Physical and chemical properties of copper slag are pre-sented in Table 1. Experimental Investigation Mix Design and Sample Preparation for Brick Masonry Prisms The mix proportion used for this study is given in Table 2.

the copper slag can be alternatively used. 3) Vast quantities of copper slag are produced from manufacturing of copper.In our project we are using the copper slag by replacing natural fine aggregate at different percentage like (0%, 20%, 40%, 60%, 80%, and 100%). B. Objective of the Investigation 1) The use of copper slag in the concrete as a ...

3.4 Copper slag:- Copper Slag with sp. gravity 3.51and moisture content max 2.0% and bulk density 1.9- 2.4% as per chemical analysis of copper slag.in copper slag the silica content and iron oxide content in copper slag was found to be 26% and 60% respectively. 3.5 Silica fume:-

Behavior of Copper Slag Admixed Concrete in Acidic Environment ... Sand is majorly used fine aggregate in the preparation of concrete, however heavy depletion of river beds and rising cost of sand have made the builders and construction industry to ... Mix Design and Different Mixes Mix Design was done as per the code book, IS: 10262 – ...

Aug 12, 2019 Design of Experiment and Mix Design of Concrete Samples. This experiment intended to optimize four key variables (copper slag, silica fume, cement factor, and w/b ratio). Table 2 shows the range of each variable. Nine tests were designed for the four variables. The mix design of concrete is presented in Table 3.

leachability of heavy metals in concrete are investigated. 2. Material and Experimental Procedure . 2.1. Material. The copper slag used in this research was a granulated copper slag from an Indonesian Smelter Plant operated by Mitsubishi materials corporation. ... The mix design used in this research was based on Indonesian Standards (SKSNI T ...

Jan 24, 2019 The use of copper slag in cement and concrete provides potential environmental as well as economic benefits for all related industries, Heavy metals in copper slag samples was tested by National Council for Cement and Building Materials, New …